HỖ TRỢ KHÁCH HÀNG

Bộ hiển thị lực - FS2000

Giá: Liên hệ

Bộ hiển thị lực kỹ thuật số có khe cắm thẻ nhớ SD & tốc độ trích mẫu cao: FS2000
Nhà sản xuất: Unipulse - Nhật Bản.

Tài liệu tham khảo: FS2000 force indicator.pdf
* Chức năng so sánh dạng sóng (liên tục so sánh thiết lập sóng giới hạn HI/LO và sóng đo thực tế)
* Nhiều điểm phán đoán (phán đoán OK/NOK có thể thực hiện trên nhiều điểm trong một quá trình. Max. 5 điểm)
* Loại tiêu chuẩn trang bị với đầu vào xác định thay đổi vị trí (A 2-So sánh sóng kích thước được thực hiện bằng cách sử dụng cả đầu vào lực và xác định thay đổi vị trí)
* Lưu dữ liệu đo và các giá trị cài đặt trong một thẻ nhớ SD
* Thực hiện cài đặt dễ dàng bằng cách chạm trực tiếp vào màn hình cảm ứng.
* Có thể lựa chọn loại Sink  / loại Source
* Thao tác số tốc độ cao 25000 lần/giây
* Hiển thị xu hướng  hữu ích cho việc bảo trì dự phòng.


SENSOR INPUT Sensor input for load (Fixed as strain gauge input)(6-wire)
Excitation voltageDDC 2.5, 5, 10V±10% (depending on settings)
Output current: Within 30mA
Signal input range-2.0mV/V to +2.0mV/V
AccuracyNon-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input)
Zero drift: Within 0.1μV/℃ RTI
Gain drift: Within 15ppm/℃
Low-pass filterSelectable from 10 to 10kHz (-6dB/oct.)
A/D converterSpeed: Selectable from 25000 times/sec., 5000 times/sec.
Resolution: 24bit (binary)
Analog voltage outputOutput level: Approx. 2V per 1.0mV/V input
Load resistance: 2kΩ or more
 
SENSOR INPUT Sensor input for displacement
Pulse input (Line driver)
Max. input frequency1MHz
Internal count rangeApprox. 1,000,000
Adaptable rotary encoderOutput: Incremental type 2-phase output (A/B signal output)
Also capable of single-phase output
(A-phase input used. All pulses are counted as in the plus direction.)
Output stage circuit specification: Line driver (Based on RS-422)
 
DISPLAY
Display4.3 inch TFT color LCD module
Display area: 95.0×(W)×53.9(H)mm
Dot configuration: 480×272 dot
Display frequencyFixed at 3 times/sec.
 
COMP. & JUDGE. FUNCTION
Multi point comparison mode
16ch
(setting values can be stored)
Capable of judging up to 5 hold points at the same time.
Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End
Waveform comparison mode
16ch
(setting values can be stored)
Compares the actually measured waveform against the preset Hi/Lo waveforms.
The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK.
 
PREVENTIVE MAINTENANCE SUPPORT
Trend displayShowing the trend of measurement data to help finding irregularities at early stage.
StatisticsUsing the latest 10000 measured data.
Displaying number of measurement, OK, NOK
Screen captureSaves screen capture data as bmp data.
Work name editWork name can be edited and displayed for each Work No..
Setting list displayChanged setting items comparing to master set values are highlighted.
User managementLogin ID and Password
 
INPUT / OUTPUT
Output signal16 points
Hold judgment (load, displacement)/ Load overload/ Measurement complete/
Waveform comparison judgment/ Load & displacement OK/ CPU OK/
SD card OK/ Timing output 1,2
Output Type: Sink type/source type selectable.
(Source Type is option: [ISC])
Output transistor ON at signal ON.
To connect an input unit like a PLC, connect plus
common for sink type, and minus common for source type.
Rated voltage: 30V
Rated current: 30mA
Input signal16 points
Load digital zero/ Displacement adjustment/ Measurement start/
Measurement end/ HOLD1 to 5/ Reset/ Forcibly light up the backlight/
Touch panel lock/ Work change
Input type: Plus common/Minus common selectable.
(Minus common is option: [ISC])
To connect a transistor, connect NPN output type (sink type) 
for plus common and PNP output type (source type) for minus common.
 
INTERFACE
Only one option can be installed.
USBUSB interface
ODNDeviceNet interface (option)
CCLCC-Link interface (option)
EIPEthernet/IP interface (option)
 
OPTION
ISCI/O source board
 
GENERAL SPECIFICATION
Power supply voltageDC24V (±15%)
Power consumption6W typ
Operation conditionOperation temperature: -10℃ to +40℃ / Storage temperature: -20℃ to +60℃
Humidity: 85% RH or less (non-condensing)
Dimension132(W)×98(H)×110(D)mm (not including projections)
WeightApprox. 1.0kg
 
ATTACHMENTS
I/O connector (with cover)1
Sensor connector1
Operating tool1
SD card1
Operation manual1
DeviceNet connector
(when DeviceNet option is selected)
1
CC-Link connector
(when CC-Link option is selected)
1

 

Specifications

SENSOR INPUT Sensor input for load (Fixed as strain gauge input)(6-wire)
Excitation voltageDDC 2.5, 5, 10V±10% (depending on settings)
Output current: Within 30mA
Signal input range-2.0mV/V to +2.0mV/V
AccuracyNon-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input)
Zero drift: Within 0.1μV/℃ RTI
Gain drift: Within 15ppm/℃
Low-pass filterSelectable from 10 to 10kHz (-6dB/oct.)
A/D converterSpeed: Selectable from 25000 times/sec., 5000 times/sec.
Resolution: 24bit (binary)
Analog voltage outputOutput level: Approx. 2V per 1.0mV/V input
Load resistance: 2kΩ or more
 
SENSOR INPUT Sensor input for displacement
Pulse input (Line driver)
Max. input frequency1MHz
Internal count rangeApprox. 1,000,000
Adaptable rotary encoderOutput: Incremental type 2-phase output (A/B signal output)
Also capable of single-phase output
(A-phase input used. All pulses are counted as in the plus direction.)
Output stage circuit specification: Line driver (Based on RS-422)
 
DISPLAY
Display4.3 inch TFT color LCD module
Display area: 95.0×(W)×53.9(H)mm
Dot configuration: 480×272 dot
Display frequencyFixed at 3 times/sec.
 
COMP. & JUDGE. FUNCTION
Multi point comparison mode
16ch
(setting values can be stored)
Capable of judging up to 5 hold points at the same time.
Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End
Waveform comparison mode
16ch
(setting values can be stored)
Compares the actually measured waveform against the preset Hi/Lo waveforms.
The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK.
 
PREVENTIVE MAINTENANCE SUPPORT
Trend displayShowing the trend of measurement data to help finding irregularities at early stage.
StatisticsUsing the latest 10000 measured data.
Displaying number of measurement, OK, NOK
Screen captureSaves screen capture data as bmp data.
Work name editWork name can be edited and displayed for each Work No..
Setting list displayChanged setting items comparing to master set values are highlighted.
User managementLogin ID and Password
 
INPUT / OUTPUT
Output signal16 points
Hold judgment (load, displacement)/ Load overload/ Measurement complete/
Waveform comparison judgment/ Load & displacement OK/ CPU OK/
SD card OK/ Timing output 1,2
Output Type: Sink type/source type selectable.
(Source Type is option: [ISC])
Output transistor ON at signal ON.
To connect an input unit like a PLC, connect plus
common for sink type, and minus common for source type.
Rated voltage: 30V
Rated current: 30mA
Input signal16 points
Load digital zero/ Displacement adjustment/ Measurement start/
Measurement end/ HOLD1 to 5/ Reset/ Forcibly light up the backlight/
Touch panel lock/ Work change
Input type: Plus common/Minus common selectable.
(Minus common is option: [ISC])
To connect a transistor, connect NPN output type (sink type) 
for plus common and PNP output type (source type) for minus common.
 
INTERFACE
Only one option can be installed.
USBUSB interface
ODNDeviceNet interface (option)
CCLCC-Link interface (option)
EIPEthernet/IP interface (option)
 
OPTION
ISCI/O source board
 
GENERAL SPECIFICATION
Power supply voltageDC24V (±15%)
Power consumption6W typ
Operation conditionOperation temperature: -10℃ to +40℃ / Storage temperature: -20℃ to +60℃
Humidity: 85% RH or less (non-condensing)
Dimension132(W)×98(H)×110(D)mm (not including projections)
WeightApprox. 1.0kg
 
ATTACHMENTS
I/O connector (with cover)1
Sensor connector1
Operating tool1
SD card1
Operation manual1
DeviceNet connector
(when DeviceNet option is selected)
1
CC-Link connector
(when CC-Link option is selected)
1
 


 

Option

ModelDescription
ISCI/O source board
ODNDeviceNet interface
CCLCC-Link interface
EIPEthernet/IP interface
 


 
 

Specifications

SENSOR INPUT Sensor input for load (Fixed as strain gauge input)(6-wire)
Excitation voltageDDC 2.5, 5, 10V±10% (depending on settings)
Output current: Within 30mA
Signal input range-2.0mV/V to +2.0mV/V
AccuracyNon-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input)
Zero drift: Within 0.1μV/℃ RTI
Gain drift: Within 15ppm/℃
Low-pass filterSelectable from 10 to 10kHz (-6dB/oct.)
A/D converterSpeed: Selectable from 25000 times/sec., 5000 times/sec.
Resolution: 24bit (binary)
Analog voltage outputOutput level: Approx. 2V per 1.0mV/V input
Load resistance: 2kΩ or more
 
SENSOR INPUT Sensor input for displacement
Pulse input (Line driver)
Max. input frequency1MHz
Internal count rangeApprox. 1,000,000
Adaptable rotary encoderOutput: Incremental type 2-phase output (A/B signal output)
Also capable of single-phase output
(A-phase input used. All pulses are counted as in the plus direction.)
Output stage circuit specification: Line driver (Based on RS-422)
 
DISPLAY
Display4.3 inch TFT color LCD module
Display area: 95.0×(W)×53.9(H)mm
Dot configuration: 480×272 dot
Display frequencyFixed at 3 times/sec.
 
COMP. & JUDGE. FUNCTION
Multi point comparison mode
16ch
(setting values can be stored)
Capable of judging up to 5 hold points at the same time.
Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End
Waveform comparison mode
16ch
(setting values can be stored)
Compares the actually measured waveform against the preset Hi/Lo waveforms.
The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK.
 
PREVENTIVE MAINTENANCE SUPPORT
Trend displayShowing the trend of measurement data to help finding irregularities at early stage.
StatisticsUsing the latest 10000 measured data.
Displaying number of measurement, OK, NOK
Screen captureSaves screen capture data as bmp data.
Work name editWork name can be edited and displayed for each Work No..
Setting list displayChanged setting items comparing to master set values are highlighted.
User managementLogin ID and Password
 
INPUT / OUTPUT
Output signal16 points
Hold judgment (load, displacement)/ Load overload/ Measurement complete/
Waveform comparison judgment/ Load & displacement OK/ CPU OK/
SD card OK/ Timing output 1,2
Output Type: Sink type/source type selectable.
(Source Type is option: [ISC])
Output transistor ON at signal ON.
To connect an input unit like a PLC, connect plus
common for sink type, and minus common for source type.
Rated voltage: 30V
Rated current: 30mA
Input signal16 points
Load digital zero/ Displacement adjustment/ Measurement start/
Measurement end/ HOLD1 to 5/ Reset/ Forcibly light up the backlight/
Touch panel lock/ Work change
Input type: Plus common/Minus common selectable.
(Minus common is option: [ISC])
To connect a transistor, connect NPN output type (sink type) 
for plus common and PNP output type (source type) for minus common.
 
INTERFACE
Only one option can be installed.
USBUSB interface
ODNDeviceNet interface (option)
CCLCC-Link interface (option)
EIPEthernet/IP interface (option)
 
OPTION
ISCI/O source board
 
GENERAL SPECIFICATION
Power supply voltageDC24V (±15%)
Power consumption6W typ
Operation conditionOperation temperature: -10℃ to +40℃ / Storage temperature: -20℃ to +60℃
Humidity: 85% RH or less (non-condensing)
Dimension132(W)×98(H)×110(D)mm (not including projections)
WeightApprox. 1.0kg
 
ATTACHMENTS
I/O connector (with cover)1
Sensor connector1
Operating tool1
SD card1
Operation manual1
DeviceNet connector
(when DeviceNet option is selected)
1
CC-Link connector
(when CC-Link option is selected)
1
 


 

Option

ModelDescription
ISCI/O source board
ODNDeviceNet interface
CCLCC-Link interface
EIPEthernet/IP interface
 


 
 

Specifications

SENSOR INPUT Sensor input for load (Fixed as strain gauge input)(6-wire)
Excitation voltageDDC 2.5, 5, 10V±10% (depending on settings)
Output current: Within 30mA
Signal input range-2.0mV/V to +2.0mV/V
AccuracyNon-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input)
Zero drift: Within 0.1μV/℃ RTI
Gain drift: Within 15ppm/℃
Low-pass filterSelectable from 10 to 10kHz (-6dB/oct.)
A/D converterSpeed: Selectable from 25000 times/sec., 5000 times/sec.
Resolution: 24bit (binary)
Analog voltage outputOutput level: Approx. 2V per 1.0mV/V input
Load resistance: 2kΩ or more
 
SENSOR INPUT Sensor input for displacement
Pulse input (Line driver)
Max. input frequency1MHz
Internal count rangeApprox. 1,000,000
Adaptable rotary encoderOutput: Incremental type 2-phase output (A/B signal output)
Also capable of single-phase output
(A-phase input used. All pulses are counted as in the plus direction.)
Output stage circuit specification: Line driver (Based on RS-422)
 
DISPLAY
Display4.3 inch TFT color LCD module
Display area: 95.0×(W)×53.9(H)mm
Dot configuration: 480×272 dot
Display frequencyFixed at 3 times/sec.
 
COMP. & JUDGE. FUNCTION
Multi point comparison mode
16ch
(setting values can be stored)
Capable of judging up to 5 hold points at the same time.
Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End
Waveform comparison mode
16ch
(setting values can be stored)
Compares the actually measured waveform against the preset Hi/Lo waveforms.
The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK.
 
PREVENTIVE MAINTENANCE SUPPORT
Trend displayShowing the trend of measurement data to help finding irregularities at early stage.
StatisticsUsing the latest 10000 measured data.
Displaying number of measurement, OK, NOK
Screen captureSaves screen capture data as bmp data.
Work name editWork name can be edited and displayed for each Work No..
Setting list displayChanged setting items comparing to master set values are highlighted.
User managementLogin ID and Password
 
INPUT / OUTPUT
Output signal16 points
Hold judgment (load, displacement)/ Load overload/ Measurement complete/
Waveform comparison judgment/ Load & displacement OK/ CPU OK/
SD card OK/ Timing output 1,2
Output Type: Sink type/source type selectable.
(Source Type is option: [ISC])
Output transistor ON at signal ON.
To connect an input unit like a PLC, connect plus
common for sink type, and minus common for source type.
Rated voltage: 30V
Rated current: 30mA
Input signal16 points
Load digital zero/ Displacement adjustment/ Measurement start/
Measurement end/ HOLD1 to 5/ Reset/ Forcibly light up the backlight/
Touch panel lock/ Work change
Input type: Plus common/Minus common selectable.
(Minus common is option: [ISC])
To connect a transistor, connect NPN output type (sink type) 
for plus common and PNP output type (source type) for minus common.
 
INTERFACE
Only one option can be installed.
USBUSB interface
ODNDeviceNet interface (option)
CCLCC-Link interface (option)
EIPEthernet/IP interface (option)
 
OPTION
ISCI/O source board
 
GENERAL SPECIFICATION
Power supply voltageDC24V (±15%)
Power consumption6W typ
Operation conditionOperation temperature: -10℃ to +40℃ / Storage temperature: -20℃ to +60℃
Humidity: 85% RH or less (non-condensing)
Dimension132(W)×98(H)×110(D)mm (not including projections)
WeightApprox. 1.0kg
 
ATTACHMENTS
I/O connector (with cover)1
Sensor connector1
Operating tool1
SD card1
Operation manual1
DeviceNet connector
(when DeviceNet option is selected)
1
CC-Link connector
(when CC-Link option is selected)

 
 
 



 

Option

ModelDescription
ISCI/O source board
ODNDeviceNet interface
CCLCC-Link interface
EIPEthernet/IP interface
 

 

 

Optional accessories


ModelDescription
SD1G1 GByte card
SD2G2 GByte card
SD-ADPSD Card Adapter (ATA TYPEⅡ)
CA81-USBUSB cable (A-miniB type) 1.8m