HỖ TRỢ KHÁCH HÀNG

Bộ hiển thị khối lượng - F650-CK

Giá: Liên hệ

Bộ hiển thị khối lượng cho cân tự động kiểm tra: F650-CK
Nhà sản xuất: Unipulse - Nhật Bản.

Tài liệu tham khảo: F650-CK weighing indicator.pdf
* Bộ hiển thị khối lượng đã được thiết kế cho cân kiểm tra vật di động
* Với bộ lọc với hiệu năng cao làm giảm nhiễu và rung động, việc đo khối lượng ổn định và chính xác có thể đạt được
* Tất cả các chức năng cần thiết cho cân kiểm tra như đánh giá lớn hơn/nhỏ hơn, sắp xếp hay phân loại, các phương thức cân khác nhau, điều khiển băng tải, thống kê và…. được đóng gói trong một loại

 

Specifications

Analog section
Excitation voltageDC5V±5% Output current:within 90mA Ratiometric method(Up to 6 load cells at 350Ω can be connected in parallel.)
Signal input range-0.3 to 3.0 mV/V
Zero adjustment range-0.2 to 3.0 mV/V Automatic adjustment by digital computation
Gain adjustment rangeAutomatic adjustment by digital computation
AccuracyNon-linearity:within 0.01%/FS±1digit(when 3mV/V is input)
Zero drift:0.025μV/℃ RTI Typ
Gain drift:1ppm/℃ Typ
A/D converterConversion rate : 1000 times/sec Resolution : 24bit (binary)
Theoretical calibrationEquivalent input calibration : accuracy when theoretical calibration is performed : 1/1,000
 
Filter
Digital filterMoving average (common for all modes) : OFF, 2 to 999 times
Low-pass filterVariable : 2.0 to 10.0Hz
 
Display section
Display unitTFT color LCD module 3.5inch (320×240dot) Display area : 71(W) x 53(H) mm ×53(H)mm
Weight display5-digits (signs: minus sign on the highest numerical digit)
UnitNONE, kg, t, g, N, or lb (selectable)
Decimal place0, 0.0, 0.00, or 0.000 (selectable)
Status displayBUSY, GO, EMP, SMP, COMP, NZ, STAB
 
Setting section
Setting methodSetting by analog touch panel operation (with a key click buzzer)Setting can be performed by external devices as well via RS-232C interface and so on.
Setting value memoryInitial values F.RAM (nonvolatile RAM), other values : lithium-battery-backed-up C-MOS RAM
Settings protectionSetting operation can be prohibited to prevent changes by miss-operation (LOCK 1, LOCK 2, LOCK 3).
Setting item・Standard mode (COMP MODE SEL.: COMP): 
CODE/STANDARD/OVER/UNDER/UPPER/LOWER  

・Standard mode (COMP MODE SEL.: RANK.1): 
CODE/BOUNDARY 0/BOUNDARY 1/BOUNDARY 2/BOUNDARY 3/UPPER/LOWER

・Standard mode (COMP MODE SEL.: RANK.2): 
CODE/BOUNDARY 0/BOUNDARY 1/BOUNDARY 2/BOUNDARY 3/BOUNDARY 4/ BOUNDARY 5/BOUNDARY 6/BOUNDARY 7/BOUNDARY 8/BOUNDARY 9/UPPER/LOWER 

・Checker mode: 
CODE/TAKING MODE/TRIGGER MODE/TAKING COUNT/TAKING RATIO/EMPTY COUNT/NEAR ZERO/DIGITAL LPF /MOV. AVE. FILTER/GROSS RATIO/HISTOGRAM TARGET/HISTOGRAM RANGE 

・State output: 
CODE/OUTPUT SEL. 0/OUTPUT SEL. 1※/OUTPUT SEL. 2※/OUTPUT SEL. 3※/OUTPUT SEL. 4※
※Selectable from OUTPUT, COMP, NZ, TAKING, ERROR, LOWER, STAB, RUN 

・Graph: 
CODE/GRAPHIC MODE/TRIGGER LEVEL/X END POINT/Y START POINT/Y END POINT/DRAWING WEIGHT/ PRE TRIG.VALUE/FRONT OF FILTER 

・Result: 
CODE/AVE.WEIGHT/MAX.WEIGHT/MIN.WEIGHT/CNT.OF DATA/GEN.STAN.DEV./SMP.STAN.DEV./MAX. - MIN./LATEST DATA

・Comparison: 
COMP MODE SEL./STAND. CMP SEL./COMPLETE OUT T./NEAR ZERO COMP./HI/LO COMP. SEL./PRESET TARE WGT.1 /PRESET TARE WGT.2/HOLD SELECT 

・Operation: 
MD (PERIOD)/MD (RANGE)/ZT (PERIOD)/ZT (RANGE)/INDICATE COLOR/BACKLIGHT LOW TM/BACKLIGHT ON TM/ AUTO ACCUMULAT./OUTPUT MODE/OUTPUT COMP. MODE/WGT CODE INPUT/ZT MODE/AUTO ZERO AVE./B4 FUNK. SELECT/TAKING SPEED 

・Communication: 
COMM. MODE/BAUD RATE/LENGTH/PARITY BIT/STOP BIT/TERMINATOR/FLOW CONTROL/ SI/F OUT1 SELECT/SI/F OUT2 SELECT 

・System: 
INITIALIZATION/LOCK1/LOCK2/LOCK3/PASSWORD/LANGUAGE/[GROSS/NET] KEY/[DZ] KEY/[TARE ON] KEY/ SELF CHECK DSP1/SELFCHECK DSP2/SELFCHECK MEM/SELF CHECK KEY/SELF CHECK EXT/SELF CHECK COM 

・Calibration: 
ZERO CAL./SPAN CAL./EQUIV. CAL./BALANCE WEIGHT/MIN. SCALE DIV./NET OVER/GROSS OVER/UNIT DISPLAY/ DECIMAL PLACE/DZ REGULATION VAL.
 
Total function
Histogram displayNumbers of data for each 9 weight ranges are displayed. Two set of data out of the range are displayed as well.
Weighing resultsResults are displayed for each code.
StatisticsDisplay statistics data stored on F650-CK. Display average weight, maximum weight, minimum weight, number of data, population standard deviation, sample standard deviation, difference between maximum and minimum, latest data.
 
External
External output(10)OVER or RANK1 or RANK20/GO or RANK2 or RANK21/UNDER or RANK3 or RANK22/ NONE or RANK4 or RANK23/NONE or RANK5 or STROBE/OUTPUT SEL. 0/OUTPUT SEL. 1/ OUTPUT SEL. 2/OUTPUT SEL. 3/OUTPUT SEL. 4
External input(10)CODE0/CODE1/CODE2 or KEY LOCK/Graph drawing/D/Z ON/TARE ON/TARE OFF/Accumulation command/Measurement start/Measurement reset
 
Interface
SIF2-wire serial interface
232RS-232C communication interface
485RS-485 communication interface (Modbus-RTU /UNI-format)(option)
BCOBCD parallel data output interface (Sink type)(option)
BSCBCD parallel data output interface (Source type)(option)
DAVD/A converter(voltage output) (option)
DAID/A converter(current output) (option)
ODNDeviceNet interface (option)
CCLCC-Link interface (option)
Only one option can be installed.
 
General performance
Operating voltage・Power consumption100 to 240 Vac ±10 to 15% (50/60Hz) 18W max
Operating conditionsOperation temperature range: -10 to 40℃ 
Storage temperature range: -20 to +60℃
Humidity: 80%RH or less (non-condensing)
Dimension ・Weight96(W)×96(H)×138(D)mm(Projections excluded) approx.1.0kg
 
Attachments
AC power cable (voltage resistance: 125 Vac ) (3m) ×1
Jumper cable ×2
FCN series I/O connector (with cover) ×1
Operation manual ×1
BCD output connector (when BCO option is installed) ×1
Mini screwdriver (when D/A converter option is installed) ×1
DeviceNet connector (with ODN option is installed) ×1
CC-Link connector (when CCL option is installed) ×1
 
Optional accessories
CA372-I/Ocable with FCN connector at one-end 3m
CA600-BCDCNVFCN connector 32p-57・36p cabtyre cable 0.3m
CA81-232XminiDIN-D-Sub9p cross cable 1.5m
CAAC2P-B3AC power cable 3m
CAAC3P-CEE7/7-B2AC power cable (voltage resistance: 250 Vac) 2m
CN50FCN series I/O connector (with cover)
CN51BCD output connector
CN55FCN series I/O connector (with diagonal cover)
CN60circular DIN 8p connector for RS-232C
CN71CC-Link connector
CN80analog I/O connector terminal
CND01DeviceNet connector
DTC2-PSLcase for F650
GMP96×96rubber seal