HỖ TRỢ KHÁCH HÀNG

Bộ hiển thị khối lượng - F800

Giá: Liên hệ

Bộ hiển thị khối lượng All-in-one: F800
Nhà sản xuất: Unipulse - Nhật Bản.

Tài liệu tham khảo: F800 weighing indicator.pdf
* Bộ chuyển đổi A/D tốc độ cao và khả năng xử lý kỹ thuật số mạnh mẽ 100 lần/giây
* Bộ nhớ mã cho 100 loại công thức mẻ cân
* Chức năng cân liên tục thuận tiện cho ứng dụng cân tự động
* Bộ lọc mạnh mẽ chống  lại rung lắc trong các hệ thống cơ khí.
* Chức năng thống kê các giá trị khối lượng cho mỗi mã.

 

Specifications

ANALOG SECTION
Excitation voltage10V DC ±5%, Output current; within 120mA (Up to 4 units at 350Ω are parallel-connectable)
Zero adjustment range0 - approx. 2mV/V (digital adjustment)
Gain adjustment range0.3 - 2.0mV/V (digital adjustment)
Min. input sensitivity0.3μV / count
AccuracyNon-linearity: within 0.01%/FS (Typ: 0.005%/FS at room temperature)
Zero drift: within 0.1μV/°C RTI (Typ: 0.08μV/°C) 
Gain drift: within 15 ppm/°C (Typ: 5 ppm/°C) 
Noise: within 0.1μVp-p RTI (0.1 - 10 Hz)
Analog filterBessel low-pass filter (-12dB/oct.), Selectable from 2, 4, 6, 8 Hz 
A/D converterSpeed: 100 times/sec 
Resolution: 16 bit (binary)
Min. display resolution1/10000
Secondary calibrationCalibration can be carried out without an actual load by connecting a resistor to one of the bridges of a loadcell.
 
SETTING SECTION
Setting methodKeyboard operation (keyboard with a key click buzzer)
External setting is available by installing RS-232C option.
Setting value storage・ Initial set values: NOV RAM (Non-volatile RAM)
・ Other set values: C-MOS RAM with backup of a lithium battery (Effective for more than 5 years depending on usage conditions and storage environment)
Setting value protectionSetting operation can be locked to prevent unauthorized modifications of default values and calibration by malfunction (LOCK)
Setting item・Calibration……Zero calibration / Span calibration/Balance weight value / Capacity / Min. scale division / Over Net / Over Gross / Display frequency / Decimal point / 1/4 Scale display ON/OFF / Unit / Gravitational acceleration compensation 
・Comparative setting1……SP1 / SP2 / CPS / Final / Under / Over / AFF reg / Compensation input timer 
・Comparative setting2……Near zero / Lo / Hi / Preset tare weight / Comparison inhibit time / Judging time / Compare time / Discharging time / AZ time / Judging times / Sequence mode 
・Function setting……Digital filter / Motion Detection / Weighing function1 / Weighing function2 / Weighing function3 / Function key inhibited / RS-232C / ID number setting / Analog filter / Zero tracking / Measurement law / Extended selection
 
INPUT/OUTPUT SECTION
External output signal (16 points)・Transistor open collector output. (Emitter=COM terminal) The output turns ON when the transistor turns ON.
・Near zero / SP1 / SP2 / SP3 / under / go / over / complete / discharge / Lo / Hi / stable / weight error / error / final error / RUN
External Input signal (23 points)・ON when shorted with COM terminals by contact (relay, switch, etc.) or non-contact (transistor, TTL open-collector output, etc.)
・Gross or net / digital zero / tare on / tare reset / hold or judge / feed or discharge / accumulation command / accumulation clear / code setting / start / stop / discharge command / compulsory discharge command / discharge gate open / discharge gate close / code assign selection / code assign input
INTERFACE・ SIF:2-wire type serial interface (standard); Interface to link with Unipulse printer or external display
・ BCO:BCD parallel data output interface(Option)……Transmits weight data to a PLC or other BCD devices.
・ 232:RS-232C communication interface (Optional): Write (change) / read weight data, various statuses and setting values via commands from host computer
・ BCI:BCD parallel data input interface (Option)……Parallel interface to receive setting values from external devices.
・ 485:RS-485 communication interface (Option)……Compared with the RS-232C, longer-distance communications can be carried out.
・ DAC:D/A converter (Option)……Weighing values are output as converted into analog signals of voltage and current. The zero output weight value and full scale value can be set.
・ ODN:DeviceNet interface (Option)……Seamlessly connectable with DeviceNet-compliant Omron CompoBus/D.
・ CCL:CC-Link interface(Option)……Serial bus interface for connection with PLC
 
DISPLAY SECTION
Weight displayNumerical display (8-digit) by fluorescent display tube 12mm in character height
Weight value display5 digits Sign: Only a negative sign is displayed at the highest-order digit of the display.
Unitt, g, kg, none selectable
Decimal pointDisplay position selectable (zero blanking display by decimal point)
Display update rate3, 6, 13, 25 times/sec. selectable (However, the A/D conversion rate is fixed.)
Capacity5 digits settable
Over scale displayA/D converter input over(LOAD)
Net over (5 digits settable)(OFL1) 
Gross weight beyond capacity + 9 scale divisions(OFL2)
Gross over (5 digits settable)(OFL3)
Center zero displayDisplays true zero point (1/4 scale division).
Status displayFixed character display by fluorescent display tube (display item lighting) SET / LOCK / HOLD / Z.ALM / STAB. / T.SET / NET / GROSS / RUN / UPER LV / LOWR LV / NEAR Z. / SP1 / SP2 / SP3 / OVER / GO / UNDER / COMPL / D.CHG / AFC
Setting value displayBy fluorescent display tube 4mm in character height CODE / FINAL / UNDER / OVER / SP1 / SP2 / CPS
Accumulation displayBy fluorescent display tube 4mm in character height
No. displayBy fluorescent display tube 4mm in character height
ALARM (2-digit) / SEQ.NO. (3-digit)
 
GENERAL SPECIFICATIONS
Power supply voltage85 - 110V, 102 - 132V, 170 - 220V, 187 - 242V AC (Please specify when ordering), 50/60 Hz
Power consumptionApprox. 20VA
Operating conditionsTemperature: Working temperature range -10°C - +40°C; Storage temperature range -40 - +80°C
Humidity: 85% RH or less (non-condensing)
External dimensions130 (W) x 207 (H) x 150 (D) [mm] (protruding parts not included)
Panel cutout dimensions127 (W) x 200 (H) mm *Installation panel thickness: 1.6 mm or more
WeightApprox. 3 kg
 
ACCESSORIES
Power supply cable (2 m)1
Spare fuse (1A)1
Load cell input connector (Hirose JR16PN-7S)1
Control signal input/output connector (DDK 57-30500)1
Flathead screwdriver1
Operation manual1
BCD output connector (when BCD output option is selected)1
BCD input connector (when BCD input option is selected)1
DeviceNet connector (when DeviceNet output option is selected)1
CC-Link interface (when CC-Link option is selected)1
 

Option

ModelOptional slot・・・3(Please refer to the following table for the combination that can be installed.)
BCOBCD parallel data output interface
232RS-232C communication interface
BCIBCD parallel data input interface
485RS-485 communication interface
DACD/A converter
ODNDeviceNet interface
CCLCC-Link interface
 

(Ref.) Assortment of options

Number of install OPBCD OUT
(BCO)
BCD IN
(BCI)
D/A
(DAC)
RS-232C
(232)
RS-485
(485)
DeviceNet
(ODN)
CC-Link
(CCL)
1        
        
        
        
        
       ◎ 
        
2       
       
       
       
      ◎ 
       
       
       
       
      ◎ 
       
       
       
      ◎ 
       
3      
      
      
      
      
      
Number of install OPBCD OUT
(BCO)
BCD IN
(BCI)
D/A
(DAC)
RS-232C
(232)
RS-485
(485)
DeviceNet
(ODN)
CC-Link
(CCL)
 

 

 

Optional accessories

ModelDescription
CAAC2P-P2AC input cord 2 m
CAAC3P-CEE7/7-P1.5AC input cord (withstand pressure: 250V) 1.5m
CN3P-2P3P-2P conversion plug for AC input cord
CA4131(6-core) cable with JR connector at one end (cable end is separated) 3 m
CA4230JR-PRC conversion relay (6-core) cable 0.3 m
CA4311JR-PRC conversion relay (6-core) 4-wire type / 6-wire type (for 520A) 1m
CN21BCD input/output connector
CN2257 series 50p connector for external I/O
CN35D-Sub 25p connector for RS-232
CN71CC-Link connector
CND01DeviceNet connector