HỖ TRỢ KHÁCH HÀNG

Bộ hiển thị khối lượng - FC1000

Giá: Liên hệ

Bộ hiển thị khối lượng với độ bền môi trường cao: FC1000
Nhà sản xuất: Unipulse - Nhật Bản.

Tài liệu tham khảo: FC1000 weighing indicator.pdf
* Chức năng kiểm soát toàn bộ khối lượng 
* Tốc độ lấy mẫu & đáp ứng cao
* Bộ lọc hiều quả cao
* Điều chỉnh lọc tự động
* Cấp độ bảo vệ IP65
* Không cần ghi dữ liệu trên SD Card Printer 
* Màn hình LCD màu trăng hiển thị 20 chữ số
* Chức năng điều khiển quá trình cân cơ bản
* Hiệu chỉnh đầu vào tương đương
* Hiệu chuẩn đa điểm (tuyến tính)
* Hiển thị giá trị đầu vào chuyển đổi
* Kích thước DIN 144×72 gọn nhẹ
* Bộ nhớ với 32 cài đặt khối lượng

 

Specifications

Analog
Excitation voltageDC5V±5% Output current:90mA
Remote sense type (Up to 6 350Ω load cells can be connected in parallel)
Signal input range-2.5 to +5.1mV/V
Zero adjustment rangeAutomatic adjustment by digital processing -2.5 to +2.0mV/V
Span adjustment range

Automatic adjustment by digital processing 0.02 to +3.0mV/V

Gain correctionUp to three point multi-point calibration is possible using linearization function
Min. input sensitivity0.15μV/count
AccuracyNon-linearity: within 0.01%FS
Zero drift: 0.0002%FS/℃ Typ
Gain drift: 1ppm/℃ Typ
FilterDigital low-pass filter 0.1 to 300.0 Hz
Moving average filter OFF, 2 to 512 times
A/D converterSpeed: 300 times/sec, 1200 times/sec
Resolution: 24bit binary
 
Display
Display Unit7-segment LCD display
Main display: 8 digit(14.35mm character height),
sub-display: 20 digit (4.34mm character height)
Display value5 digit sign: negative display at the highest digit (Up to 6 digits)
UnitNone / kg / g / t / lb / N
Decimal point0、0.0、0.00、0.000
Weight errors"LOAD": sensor signal level is above the signal input range, "-LOAD": the sensor signal level is below the signal input range, "OFL1": the Net weight is over the limit, "OFL3": the GROSS weight is over the limit
Display frequency1, 3, 6, 13 or 25 times/sec.
Status displaySP1/SP2/SP3/COMPLETE/TARE ON/NET/OUT1/OUT2
 
Setting
Setting methodBy operating the membrane keys or through interface
Memory of set valueDefault settings: stored in NOV.RAM(non-volatile RAM)
Time: backed up by lithium battery
Other setting values: stored in F-RAM(non-volatile RAM)
Protection of set valueSettings can be protected with the software LOCK
Setting item- Comparison Inhibit Time 1 / Judging Time / Complete Output Time / Compensation Feeding Time / AZ Times / Judging Times / Auto Free Fall Compensation Limit / Comparison Inhibit Time 2 / Tare Weight
- Weighing Function 1 / Weighing Function 2 / Weighing Function 3 / Sequence Mode / Lock Function Keys / Discharge Time / Motion Detection(Time & Range) / Zero Tracking Time / Zero Tracking Range
- Weighing Function 1 / Weighing Function 2 / Weighing Function 3 / Sequence Mode / Lock Function Keys / Discharge Time / Motion Detection(Time & Range) / Zero Tracking Time / Zero Tracking Range
- Balance Weight Value / Minimum Scale Division / Net Over / Gross Over / DZ Regulation / Function Selection / Gravitational Acceleration / Sampling Speed / Sub display Selection
- D/A Output Mode / D/A Zero Output Weight / D/A Full Scale / RS-232C / RS-485 Setting / ID Number / Delay Time / CC-Link Number / CC-Link Station / Level Signal Priority
- Input Selection 1 / Input Selectin 2 / Output Selection 1 / Output Selection 2 / Output Selection 3 / Status Display Selection / Automatic Filter Adjustment / Digital Low Pass Filter / Moving Average Filter
- Batch Count / SP0 / Total Weight Comparison Selection / Target Total Weight (Upper 4 digit) / Target Total Weight (Lower 5 digit) / Total Weight Set Point (Upper 4 digit) / Total Weight Set Point (Lower 5 digit)
- Read Settings from the SD Card / Write the Settings on the SD Card / Protect Settings / Extended Function Selection 1 / Extended Function Selection2 / Total weight control function
- Average Weight / Max. Value / General Standard Deviation / Data Count / Latest Data / Max.-Min. / Option Board Confirmation
- Span Calibration / Equivalent Input Span Calibration / Equivalent Input Zero Calibration / Linearize Calibration1 / Linearization Calibration2 / Linearization Calibration3 / Linearization Calibration ON/OFF / Calibration Point Confirmation / Password / Zero Calibration
 
External signal
Output signal(12)Selectable/configurable
Open collector output
Vceo=30V, Ic=120mA
Input signal(8)Selectable/configurable
Non-voltage contact input
(internal circuit power supply voltage 12V)
 
Interface
·SI/F interface
·SD card slot
·Select either RS-232C or RS-485 interface
·BCD parallel data output interface (Option)
·D/A converter current output (Option)
·CC-Link interface (option)
 
General specification
Power supply voltageAC100 to 240V (+10% -15%) (free power source 50/60Hz)
Power consumption5W typ
Operating conditionsTemperature Operating temperature range: -10 to +50℃
Storage temperature range: -20 to +60℃
Humidity 85%RH or less(non-condensing)
Dimensions144(W) × 72(H) × 109(D) mm (excluding the projections)
WeightApprox. 850g
 
Attachment
·AC input cord (nominal rating 125V) 3m···1
·FCN series I/O connector (with cover)···1
·Jumper cable···2
·SD card (1GB)···1
·Rubber seal for dust & drop-proof protection···1
·Quick manual···1
·BCD output connector (when BCO option is selected)···1
·D/A converter connector (when DAC option is selected)···1
·CC-Link connector (when CC-Link option is selected)···1