HỖ TRỢ KHÁCH HÀNG

Bộ hiển thị khối lượng - F805AT

Giá: Liên hệ

Bộ hiển thị khối lượng màn hình cảm ứng/hiển thị hình họa: F805AT
Nhà sản xuất: Unipulse - Nhật Bản.

Tài liệu tham khảo: F805AT weighing indicator.pdf
* Ứng dụng màn hình cảm ứng, màu tinh thể lỏng
* Bộ chuyển đổi A/D tốc độ cao và khả năng xử lý số mạnh mẽ 1000 lần/ giây
* Kết nối trực tiếp với PLC
* Bộ nhớ dữ liệu cho 100 công thức đợt cân
* Chức năng cân liên tục thuận tiện cho việc cân tự động 
* Hiển thị giá trị cân dạng sóng và các điểm toàn dải,  đoạn nhỏ … có thể được giám sát

 

Specifications

ANALOG SECTION
Excitation voltage10V or 5V DC±5% (digital adjustment), Output current; within 120mA, remote sense type (Up to 4 loadcells at 350Ω are parallel-connectable.)
Zero adjustment range0 - approx. 2mV/V (digital adjustment)
Gain adjustment range0.3 - 2.0mV/V (digital adjustment)
Min. input sensitivity0.3μV/count (at valid 1/4 scale division), 0.075μV/count (at invalid 1/4 scale division)
AccuracyNon-linearity: within 0.01%/FS (Typ: 0.005%/FS at room temperature)
Zero drift: within 0.1μV/°C RTI (Typ: 0.08μV/°C) 
Gain drift: within 15 ppm/°C (Typ: 5 ppm/°C) 
Noise: within 0.1μVp-p RTI (0.1 - 10 Hz)
Analog filterBessel low-pass filter (-12dB / oct.) selectable from 2, 4, 6, 8 Hz
A/D converterSpeed: 1000 times/sec (switchable to 200 times/sec)
Resolution: 16 bit (binary)
Min. display resolution1/10000 (at valid 1/4 scale division), 1/40000 (at invalid 1/4 scale division)
Secondary calibrationEquivalent input calibration method that allows calibration by simply key-inputting the rated value of a sensor without applying an actual load
Min. calibration resolution at secondary calibration (1/1000 at room temperature)
 
SETTING SECTION
Setting method・Setting by touch panel operation
・Setting from host computer via RS-232C is also possible.
Setting value storage・Default: NOV RAM (nonvolatile RAM)
・Other setting values: C-MOS RAM with backup of a lithium battery (Depends on usage conditions and storing environment, but memory can be kept for approx. 7 years or more.)
Setting value protectionSetting operation can be locked to prevent unauthorized modifications of default values and calibration by malfunction (LOCK)
 
INPUT / OUPUT SECTION
External signal output- Logic: Transistor’s open collector output (Emitter = COM terminal); Output is LO when transistor is ON.
- Near zero, SP1, SP2, SP3, Under, go, over, comp, discharge, Low limit, high limit, stable, weight alarm, error, final error, run or total limit External signal input
External signal input- Input is ON when shorted to COM terminal by contact (relay switch, etc.) or non contact (transistor, open collector, etc.).
- Gross / Net weight change, Digital zero, Tare off, Tare reset, Hold or judge, Feed / discharge change, Accumulation command, Accumulation clear, Start, Stop, Discharge command, Code No. designation, Forced-discharge command, Discharge gate open, Discharge gate close, Code No. designation selection, Graph drawing
Weighing code selection inputBCD 2 digits (00 - 99), 100 codes
Interface・ SIF:2-wire type serial interface (standard); Interface to link with Unipulse printer or external display
・ SI2:2-wire type bi-directional serial interface (standard): Interface to link with peripherals such as a printer or display
・ 232:RS-232C communication interface (standard): Write (change) / read weight data, various statuses and setting values via commands from host computer
・ BCO:BCD parallel data output interface (Optional): Parallel interface to transmit weight data to various peripherals
・ BCI:BCD parallel data input interface (Optional): Parallel interface to receive various setting values from external unit
・ 485:RS-485 communication interface (Optional): Allows longer-distance communication than RS-232C. ID numbers are set, and multiple units of F805AT are parallel-connectable.
・ DAC:D/A converter interface (Optional): Interface to convert weight data to current signal and output it
・ CCL:CC-Link interface (Optional): Interface to link F805AT with network such as MITSUBISHI general-purpose sequencer
・ ODN:DeviceNet interface (Optional): Interface to link F805AT with DeviceNet such as OMRON CompoBus/D
 
DISPLAY SECTION
DisplayTFT color LCD (Display area 116.8 (W) x 88.0 (H) [mm], 320 x 240 dot
Weight value display5 digits, Minus sign on most significant digit.
UnitSelectable from t, kg, g, N, lb, none
Decimal pointSelectable 0. 0.0, 0.00, 0.000
Display update rateSelectable from 3, 6, 13, 25 times/sec (A/D conversion rate is fixed.)
Scale capacity5-digit numerical values (up to 99999)
Over displayLOAD (A/D converter input over), OFL1; (Net weight > Net over set value) [5-digit setting], OFL2: (Gross weight >Capacity +9 scale divisions). OFL3; Gross weight > Gross over set value (5-digit setting)
Center zeroTrue zero point (0±1/4 scale) or the center of each value is displayed.
Status displayLOCK, HOLD, ZALM, STAB, TARE, RUN, HI, LO, NZ, SP1, SP2, SP3, OVER, GO, UNDER, COMPL, DCHG
Set value displayCODE, FINAL, OVER, UNDER, BEFORE FINAL, FF
Accumulation displayAccumulation times (4 digits), Accumulation value (9 digits)
No. displayAlarm No. (2 digits): Error No. in sequence control
Sequence No. (3 digits): Process No. in sequence control
 
GENERAL SPECIFICATIONS
Excitation voltage100 - 240V AC (+10% - 15%) (Free power supply 50/60 Hz)
12 - 24V DC (±15%) (Please specify when ordering)
Power consumption20W
Inrush current (Type)15A, 5msec: 100V AC average load condition (cold start at room temperature)
30A, 5msec: 200V AC average load condition (cold start at room temperature) 
10A, 0.5msec: 12V DC average load condition (cold start at room temperature) 
35A, 0.4msec: 24V DC average load condition (cold start at room temperature)
Operating conditionsTemperature: Operating temperature range -10 - +40°C; Storage temperature range -20 - +60°C
Humidity: within 85% RH (no condensing)
External dimensions174 (W) x 135 (H) x 159 (D) mm (protruding part not included)
Panel cutout dimensions165 (W) (+2 - 0) x 130 (D) [mm]
Panel thickness1.6 - 3.2 mm
WeightApprox. 2.3 kg
CE marking certificationEMC directives  EN61326-1
Safety standard  EN61010-1, EN62311
(Please specify requirement for CE marking certified product when making your order)
(DC power supply is not certificationed to CE Marking. )
 
OPTION
BCOBCD parallel data output interface
BCIBCD parallel data input interface
DACD/A converter interface (2ch interface installed)
485RS-485 communication interface*
ODNDeviceNet interface*
CCLCC-Link interface*
Number of option installationsUp to 4 options and 1 serial communication interface are available. (With*, only 1 option is available.)
 
ACCESSORIES
AC input cord (2m), (only for AC specifications)1
AC input cord replacement plug (only for AC specifications and CE compatibility)1
Mini-driver for terminal block connection1
Loadcell connector1
External I/O signal connector1
Operation Manual1
Ferrite core (only for CE compatibility)2
BCD output connector (with BCD output option)1
BCD input connector (with BCD input option)1
D/A converter connector (with D/A converter)1
CC-link connector (with CC-Link option)1
DeviceNet connector (with DeviceNet option)1

Option

ModelInterfaceSlots installed
BCOBCD parallel data output interface
(General-purpose slot option…3 slots installed (① to ③below))
1~3
BCIBCD parallel data input interface
(General-purpose slot option…3 slots installed (① to ③below))
1~3
DACD/A converter interface
(General-purpose slot option…3 slots installed (① to ③below))
1~3
485RS-485 communication interface
(Advanced communication slot option…1 slot installed (④ below))
4
ODNDeviceNet interface
(Advanced communication slot option…1 slot installed (④ below))
4
CCLCC-Link interface
(Advanced communication slot option…1 slot installed (④ below))
4
 

Slot chart

 
 

Optional accessories

ModelDescription
CAAC3P-P2AC input cord 2 m
CAAC3P-CEE7/7-P1.5AC input cord (withstand pressure: 250V) 1.5m
CA4131(6-core) cable with JR connector at one end (cable end is separated) 3 m
CA4230JR-PRC conversion relay (6-core) cable 0.3 m
CA4311JR-PRC conversion relay (6-core) 4-wire type / 6-wire type (for 520A) 1m
CN3P-2P3P-2P conversion plug for AC input cord
CN20D/A converter connector
CN21BCD I/O connector
CN2257 series 50p connector for external I/O
CN34D-Sub 9p connector for RS-232C
CN71CC-Link connector
CND01DeviceNet connector
TSU02Lightning surge unit
TSU03Lightning surge unit DS specification
GMP165×130Rubber packing