| Analog section | |
| Excitation voltage | DC5V±5% Output current: within 90mA Ratiometric method (Up to 6 load cells at 350Ω can be connected in parallel.) |
|---|---|
| Signal input range | -0.3 to 3.0 mV/V |
| Zero adjustment range | -0.2 to 3.0 mV/V Automatic adjustment by digital computation |
| Gain adjustment range | Automatic adjustment by digital computation |
| Accuracy | Non-linearity: within 0.01%/FS±1digit (when 3mV/V is input) Zero drift: 0.025μV/℃ RTI Typ Gain drift: 1ppm/℃ Typ |
| A/D converter | Conversion rate: 1000 times/sec. Resolution: 24bit (binary) |
| Min. display resolution | 1/10000 |
| Theoretical calibration | Equivalent input calibration: accuracy when theoretical calibration is performed: 1/1,000 |
| Filter | |
| Digital filter | Moving average (common for all modes): OFF, 2 to 999 times |
|---|---|
| Low-pass filter | Variable: 2.0 to 10.0Hz |
| Display section | |
| Display unit | TFT color LCD module 3.5inch (320×240dot) Display area: 71(W) x 53(H) mm |
|---|---|
| Weight display | 5-digits (signs: minus sign on the highest numerical digit) |
| Unit | NONE, kg, t, g, N, or lb (selectable) |
| Decimal place | 0, 0.0, 0.00, or 0.000 (selectable) |
| Status display | BUSY, GO, EMP, SMP, COMP, NZ, STAB |
| Setting section | |
| Setting method | Setting by analog touch panel operation (with a key click buzzer) Setting can be performed by external devices as well via RS-232C interface and so on. |
|---|---|
| Setting value memory | Initial values F.RAM (nonvolatile RAM), other values : lithium-battery-backed-up C-MOS RAM |
| Settings protection | Setting operation can be prohibited to prevent changes by miss-operation (LOCK1, LOCK2, LOCK3). |
| Setting item | ・Standard mode (COMP MODE SEL.: COMP): CODE/ STANDARD/ OVER/ UNDER/ UPPER/ LOWER ・Standard mode (COMP MODE SEL.: RANK.1): CODE/ BOUNDARY 0/ BOUNDARY 1/ BOUNDARY 2/ BOUNDARY 3/ UPPER/ LOWER ・Standard mode (COMP MODE SEL.: RANK.2): CODE/ BOUNDARY 0/ BOUNDARY 1/ BOUNDARY 2/ BOUNDARY 3/ BOUNDARY 4/ BOUNDARY 5/ BOUNDARY 6/ BOUNDARY 7/ BOUNDARY 8/ BOUNDARY 9/ UPPER/ LOWER ・Checker mode: ・State output: ・Graph: ・Result: ・Comparison: ・Operation: ・Communication: ・System: ・Calibration: |
| Total function | |
| Histogram display | Numbers of data for each 9 weight ranges are displayed. Two set of data out of the range are displayed as well.d> |
|---|---|
| Weighing results | Results are displayed for each code. |
| Statistics | Display statistics data stored on F650-CK. Display average weight, maximum weight, minimum weight, number of data, population standard deviation, sample standard deviation, difference between maximum and minimum, latest data. |
| External signal | |
| External output (10) | OVER or RANK1 or RANK20/ GO or RANK2 or RANK21/ UNDER or RANK3 or RANK22/ NONE or RANK4 or RANK23/ NONE or RANK5 or STROBE/ OUTPUT SEL. 0/ OUTPUT SEL. 1/ OUTPUT SEL. 2/ OUTPUT SEL. 3/ OUTPUT SEL. 4 |
|---|---|
| External input (10) | CODE0/ CODE1/ CODE2 or KEY LOCK/ Graph drawing/ D/Z ON/ TARE ON/ TARE OFF/ Accumulation command/ Measurement start/ Measurement reset |
| Interface | |
| SIF | 2-wire serial interface |
|---|---|
| 232 | RS-232C communication interface |
| 485 | RS-485 communication interface (Modbus-RTU/ UNI-format) (option) |
| BCO | BCD parallel data output interface (Sink type) (option) |
| BSC | BCD parallel data output interface (Source type) (option) |
| DAV | D/A converter(voltage output) (option) |
| DAI | D/A converter(current output) (option) |
| ODN | DeviceNet interface (option) |
| CCL | CC-Link interface (option) |
| Only one option can be installed. | |
| General performance | |
| Operating voltage・Power consumption | 100 to 240 Vac ±10 to 15% (50/60Hz) 18W max |
|---|---|
| Operating conditions | Operation temperature range: -10 to +40℃ Storage temperature range: -20 to +60℃ Humidity: 80%RH or less (non-condensing) |
| Dimensions ・Weight | 96(W)×96(H)×138(D)mm (Projections excluded) Approx. 1.0kg |
.png)
