| Analog section | |
| Excitation voltage | 5 Vdc±5% Output current: within 90mA Ratiometric method(Up to 6 load cells at 350Ω can be connected in parallel.) |
|---|---|
| Signal input range | -0.5 to 3.0mV/V |
| Zero adjustment range | -0.2 to 2.0mV/V (automatic adjustment by digital computation) |
| Gain adjustment range | 0.3 to 3.0mV/V (automatic adjustment by digital computation) |
| Minimum input sensitivity | 0.15μV/count |
| Accuracy | Non-linearity: within 0.01%/FSZero drift: 0.025μV/℃RTI TypGain drift: 1ppm/℃ Typ |
| A/D converter | Speed: 1200, 300 times/sec. (selectable)Resolution: 24bit (binary) |
| Min. display resolution | 1/10000 |
| Theoretical calibration | equivalent input calibration (accuracy when theoretical calibration is performed at ambient: 1/1,000) |
| Filter | |
| Low-pass filter | When A/D conversion rate is 1200 times/sec: 6, 8, 10, 12, 16, or 20Hz (selectable)When A/D conversion rate is 300 times/sec: 1.5, 2, 2.5, 3, 4, 5Hz (selectable) |
|---|---|
| Moving average filter | 1 to 512 times |
| Display section | |
| Display unit | Main display: numerical display (7-digit) with a character height of 18mm by fluorescent display tubeCode (blend): Character height 8mm, numerical display by 7-segment green LED (2-digit) |
|---|---|
| Weight display | 5-digits (signs: minus sign on the highest numerical digit) |
| Display frequency | 1, 2, 5, 10 and 20 times/sec (selectable) |
| Scale capacity | 5-digit numerical values |
| Minimum scale division/increment | 1 to 50 (selectable) |
| Unit of measurement | NONE, g, kg, t, or lb (selectable) |
| Decimal place | 0, 0.0, 0.00, or 0.000 (selectable) |
| Over scale display | LOAD (A/D converter input over),OFL1 (Net weight > Net over set value),OFL2 (Gross weight > Capacity +9 scale divisions),OFL3; (Gross weight > Gross over set value) |
| Center zero | Display true zero point or the center of each value |
| Status display | CLAMP, SP3, SP2, SP1, HOLD, COMPL., ZT, ZALM, STAB, TARE, NET, GROSS, NZ, D.CHG, HI, GO, LO, HI LIM, LO LIM, LOCK |
| Setting section | |
| Setting method | Can edited with using membrane switch.Setting can be performed by external devices as well via USB, RS-232C and RS-485 interface and so on. |
|---|---|
| Setting value memory | Parameter, calibration and part of other settings are stored on NOV.RAM (non-volatile memory), and all other settings are stored on F.RAM (another non-volatile memory). |
| Setting value protection | Overwrite protection by “LOCK” switch |
| Setting items | Upper Limit/ Lower Limit/ Near Zero/ Set Point 1/ Set Point 2/ Compensation/ Over/ Under/ Final/ Comparison Inhibit Time/ Judging Time/ Complete Output Time/ Compensation Feeding Time/ Auto Free Fall Compensation Regulation/ Weighing Function 1/ Weighing Function 2/ Tare Setting/ Tare Display/ Digital Low Pass Filter/ Moving Average Filter/ Sample Speed/ Motion Detection (Period-Range)/ Zero Tracking (Period)/ Zero Tracking (Range)/ Weighing Function 3/ Key Invalid ・ Lock/ Error Output Selection/ Password/ Bag Clamp Output Time/ Discharging Time/ Weighing Start Time/ AZ Times/ Judging Times/ Sequence Mode 1/ Sequence Mode 2/ Extended Function Selection 1/ Extended Function Selection 2/ I/O Input Check/ I/O Output Check/ BCD Input Check/ BCD Output Check/ RS-485 Check/ Balance Weight Value/ Capacity/ Min Scale Division/ DZ Regulation Value/ Display Selection/ Gravitational Acceleration/ Net Over/ Gross Over/ RS-485 I/F Setting/ RS-485 Communication Type/ RS-485 ID/ RS-232C I/F Setting/ RS-232C Communication Type/ D/A Output Mode/ D/A Zero Output Weight/ D/A Full Scale Value/ BCD Data Update Rate/ Zero Calibration/ Span Calibration/ Equivalent Calibration/ Output Monitor Display/ Option Display |
| External signal | |
| External output (16) | Transistor open collector output.Isolation: photo coupler, Rated voltage: 30V, Maximum current: 120mA |
|---|---|
| External intput (22) | The signal can be outputted by making short-circuit between input and common terminal.Isolation : photo coupler |
| Interface | |
| USB | USB interface |
|---|---|
| SIF | 2-wire serial interface |
| 232 | RS-232C communication interface (option) |
| BCO | BCD parallel data output interface (option) |
| DAC | D/A converter interface (option) |
| 485 | RS-485 communication interface (option) |
| There is a option board slot only for RS-232C. Another option interface (only one option) can be installed as well. | |
| General performance | |
| Operating voltage | AC100 to 240V (+10% -15%) [50/60Hz] |
|---|---|
| Rush current | 2A, 1msec:AC100V average load condition (cold start at room temperature)4A, 1msec:AC200V average load condition (cold start at room temperature) |
| Power consumption | Approx.18W |
| Operating conditions | Operation temperature range: -10 to 40℃Storage temperature range: -20 to +85℃Humidity: 85%RH or less (non-condensing) |
| Dimensions | 192(W)×96(H)×145(D) mm (Projections excluded)Panel cutout size: 186(W)×92(H) mm |
| Weight | Approx. 1.7kg |
.png)
