WEIGHING INDICATOR UNIPULSE FC1000

FC1000 is the weighing indicator with various features such as the white LCD main and sub display, dust and drip protection (Equivalent to IP65), accumulation function, data recording on SD Card, and high-speed A/D conversion rate of 1.2kHz.

Technical Information

Analog section
Excitation voltage DC5V±5% Output current：90mA
Remote sense type (Up to 6 350Ω load cells can be connected in parallel)
Signal input range -2.5 to +5.1mV/V
Zero adjustment range Automatic adjustment by digital processing -2.5 to +2.0mV/V
Span adjustment range

Automatic adjustment by digital processing 0.02 to +3.0mV/V
Linearization function Up to three point multi-point calibration is possible
Min. input sensitivity 0.15μV/count
Accuracy Non-linearity: within 0.01%FS
Zero drift: 0.0002%FS/℃ Typ
Gain drift: 1ppm/℃ Typ
Filter Digital low-pass filter 0.1 to 300.0 Hz
Moving average filter OFF, 2 to 512 times
A/D converter Speed: 300 times/sec., 1200 times/sec.
Resolution: 24bit binary
 
Display section
Display Unit 7-segment LCD display
Main display: 8 digit(14.4mm character height),
Sub-display: 20 digit (4.3mm character height)
Display value 5 digit　sign: negative display at the highest digit (Up to 6 digits)
Unit None / kg / g / t / lb / N
Decimal point 0, 0.0, 0.00, 0.000
Weight errors “LOAD”: sensor signal level is above the signal input range,
“-LOAD”: the sensor signal level is below the signal input range,
“OFL1”: the Net weight is over the limit,
“OFL3”: the GROSS weight is over the limit
Display frequency 1, 3, 6, 13 or 25 times/sec.
Status display SP1 / SP2 / SP3 / COMPLETE / TARE ON / NET / OUT1 / OUT2
 
Setting section
Setting method By operating the membrane keys or through interface
Memory of set value Default settings: stored in NOV.RAM (non-volatile RAM)
Time: backed up by lithium battery
Other setting values: stored in F-RAM (non-volatile RAM)
Protection of set value Settings can be protected with the software LOCK
Setting item – Upper limit / Lower limit / Near zero / Set point 1 / Set point 2 / Compensation / Over / Under / Final
– Comparison inhibit time 1 / Judging time / Complete output time / Compensation Feeding Time / Number of times for AZ / Number of times for judging / Auto free fall compensation regulation values / Comparison inhibit time 2 / Preset tare value
– Weighing function 1 / Weighing function 2 / Weighing function 3 / Sequence mode / Key invalid-LOCK / Discharging Time / Motion detection(Period – Range) / Zero tracking (Period) / Zero tracking (Range)
– Balance weight value / Minimum scale division / NET weight over / GROSS weight over /DZ limitation value / Display selection / Gravitational acceleration / Sub-display mode /Sub-display selection
– D/A output mode / D/A zero scale adjustment / D/A full scale adjustment / RS-232C/RS-485 setting / RS-232C/RS-485 ID / Transmission delay time / CC-Link I/F setting / CC-Link station number setting / Setting LOCK
– Input Signal selection 1 / Input Signal selection 2 / Input Signal selection 3 / Output Signal selection 1 /Output Signal selection 2 / Output Signal selection 3 / Output Signal selection 4 / Status display selection / Sampling speed
– Total count / SP0 / Total comparison mode / Target total weight (high 4) /Target total weight (under 5) / Total SP1 (high 4) / Total SP1 (under 5)
– SD card command 1 / SD card command 2 / Time and Date / Auto adjustment filter / Digital low pass filter / Moving average filter / Extended function selection 1 / Extended function selection 2 / Total weight control function
– Average weight value / Maximum weight value / Minimum weight value /General standard deviation / Sample standard deviation / Number of data / Latest data /Maximum-Minimum / Option display
– Span calibration / Equivalent span calibration / Equivalent zero calibration / Linearize calibration 1 / Linearization calibration 2 / Linearization calibration 3 / Linearization Calibration / Calibration Point Confirmation / Password / Zero Calibration
 
External signal
Output signal (12) Selectable/configurable
Open collector output
Vceo=30V, Ic=120mA
Input signal (8) Selectable/configurable
Non-voltage contact input
(internal circuit power supply voltage 12V)
 
Interface
· SI/F interface
· SD card slot
· Select either RS-232C or RS-485 interface
· BCD parallel data output interface (Option)
· D/A converter current output (Option)
· CC-Link interface (option)
 
General performance
Power supply voltage AC100 to 240V (+10% -15%) (free power source 50/60Hz)
Power consumption 5W typ
Operating conditions Temperature Operating temperature range: -10 to +50℃
Storage temperature range: -20 to +60℃
Humidity 85%RH or less (non-condensing)
Dimensions 144（W)×72（H)×109(D)mm (excluding the projections)
Weight Approx. 850g
download Request a quotation
Find similar products

We use cookies to offer you better experience and services. By continuing to use this website, you consent to the use of cookies on your devices.